-
September 11th, 2022, 02:55 PM
#11
Optimizing penetration on modern crossbows and compounds seems like an arbitrary affair. Most bows today will pass through a deer with just about any broadhead and still bury itself in the dirt. So extra blades don't hurt and sometimes they're the difference between catching an artery or not.
However on traditional gear a 2 blade head is an absolute must since you're shooting HALF the velocity of even the slowest Compound bows and crossbows.
"When you're at the end of your rope, tie a knot and hold on"
- Theodore Roosevelt
-
September 11th, 2022 02:55 PM
# ADS
-
September 14th, 2022, 07:40 PM
#12
Interesting point to share. I sighted in my Excalibur G340 with 150 gr bolt cutter broadheads when I bought it. I was a little suspect of the cutting diameter of the bolt cutters, very narrow, so I took species advise and bought G5 Striker V2 125 gr broadheads.
I figured there would be some tuning of the scope but to my surprise no adjustments needed. Just a tad left of the bullseye but not enough to worry about
Guns have two enemies................rust and government
OFAH and CCFR member
-
September 14th, 2022, 08:00 PM
#13
I've had some new broadheads delivered this week. I must have been drinking when I ordered them! Expensive broadhead, expensive shipping and had to pay duty.
Think I'm looking at 50 + each. Ordered 6.
They are Iron Will 100 grain crossbow.
Will have them on the R10 for archery moose which is quickly coming up
Sent from my SM-G986W using Tapatalk
-
September 14th, 2022, 08:44 PM
#14
Quote: I must have been drinking when I ordered them.
Yikes....$50.00 each for a broadhead. Hope they are made of gold
Guns have two enemies................rust and government
OFAH and CCFR member
-
September 15th, 2022, 10:37 AM
#15
No. Not gold.
A2 tool steel and titanium.
Was listening to a meateater pod cast and was sold on the materials and expectations/durability.
Sent from my SM-G986W using Tapatalk
-
September 19th, 2022, 07:51 AM
#16
Originally Posted by
chesapeake
I've had some new broadheads delivered this week. I must have been drinking when I ordered them! Expensive broadhead, expensive shipping and had to pay duty.
Think I'm looking at 50 + each. Ordered 6.
They are Iron Will 100 grain crossbow.
Will have them on the R10 for archery moose which is quickly coming up
Sent from my SM-G986W using Tapatalk
It's the right call IMO. I have heard really good things about those broad heads; I'm drinking the Kool-Aid and switched to a heavy single bevel setup as well. If you add up the cost of your bow, gear, gas, tags etc. why cheap out on the broadhead when it's the one thing that actually makes contact and does the deed?
-
September 19th, 2022, 01:31 PM
#17
Originally Posted by
MihajloSimsic
However on traditional gear a 2 blade head is an absolute must since you're shooting HALF the velocity of even the slowest Compound bows and crossbows.
Hey man, don't tell that to the animals i'll killed with my recurve and 3 blade VPA's.
3 bear and 2 deer, all pass thrus in the past few years with a traditional bow. Sharp heads + heavy arrows
Last edited by LowbanksArcher; September 19th, 2022 at 03:27 PM.
A trophy is in the eye of the bow holder
-
September 19th, 2022, 04:21 PM
#18
Has too much time on their hands
Originally Posted by
LowbanksArcher
Hey man, don't tell that to the animals i'll killed with my recurve and 3 blade VPA's.
3 bear and 2 deer, all pass thrus in the past few years with a traditional bow. Sharp heads + heavy arrows
Yeah but you are a god
They say a man turns old when sorrow and regret take the place of hope and dreams
-
September 21st, 2022, 11:39 AM
#19
Originally Posted by
LowbanksArcher
Hey man, don't tell that to the animals i'll killed with my recurve and 3 blade VPA's.
3 bear and 2 deer, all pass thrus in the past few years with a traditional bow. Sharp heads + heavy arrows
I honestly don't think a good number of the population understand what "sharp" actually is
most run of the mill broadheads need to be sharpened straight out of the package. some just need to be stropped others actually need to be ground to a proper edge from brand new.
with the right setup pass throughs are the norm
I shoot a 508grn arrow at 279fps with 18% FOC and never have an issue with penetration
-
September 22nd, 2022, 10:16 AM
#20
Originally Posted by
DanE
I honestly don't think a good number of the population understand what "sharp" actually is
most run of the mill broadheads need to be sharpened straight out of the package. some just need to be stropped others actually need to be ground to a proper edge from brand new.
with the right setup pass throughs are the norm
I shoot a 508grn arrow at 279fps with 18% FOC and never have an issue with penetration
Absolutely. My forearms tend to be clean shaven throughout deer season as i'm constantly checking blade sharpness . Especially since I'm always practicing with broadheads and constantly touching them up. Even pushing your heads into the foam of your arrow quiver will have an impact of their edge.
I'm typically around 650gr at 150-160fps, and around 20%foc with my traditional bow setup
A trophy is in the eye of the bow holder